Request Routing

This task shows you how to route requests dynamically to multiple versions of a microservice.

Before you begin

About this task

The Istio Bookinfo sample consists of four separate microservices, each with multiple versions. Three different versions of one of the microservices, reviews, have been deployed and are running concurrently. To illustrate the problem this causes, access the Bookinfo app’s /productpage in a browser and refresh several times. The URL is http://$GATEWAY_URL/productpage, where $GATEWAY_URL is the External IP address of the ingress, as explained in the Bookinfo doc.

You’ll notice that sometimes the book review output contains star ratings and other times it does not. This is because without an explicit default service version to route to, Istio routes requests to all available versions in a round robin fashion.

The initial goal of this task is to apply rules that route all traffic to v1 (version 1) of the microservices. Later, you will apply a rule to route traffic based on the value of an HTTP request header.

Route to version 1

To route to one version only, you configure route rules that send traffic to default versions for the microservices.

  1. Run the following command to create the route rules:

Istio uses virtual services to define route rules. Run the following command to apply virtual services that will route all traffic to v1 of each microservice:

Zip
$ kubectl apply -f @samples/bookinfo/networking/virtual-service-all-v1.yaml@

Because configuration propagation is eventually consistent, wait a few seconds for the virtual services to take effect.

  1. Display the defined routes with the following command:
$ kubectl get virtualservices -o yaml
- apiVersion: networking.istio.io/v1beta1
  kind: VirtualService
  ...
  spec:
    hosts:
    - details
    http:
    - route:
      - destination:
          host: details
          subset: v1
- apiVersion: networking.istio.io/v1beta1
  kind: VirtualService
  ...
  spec:
    hosts:
    - productpage
    http:
    - route:
      - destination:
          host: productpage
          subset: v1
- apiVersion: networking.istio.io/v1beta1
  kind: VirtualService
  ...
  spec:
    hosts:
    - ratings
    http:
    - route:
      - destination:
          host: ratings
          subset: v1
- apiVersion: networking.istio.io/v1beta1
  kind: VirtualService
  ...
  spec:
    hosts:
    - reviews
    http:
    - route:
      - destination:
          host: reviews
          subset: v1

You can also display the corresponding subset definitions with the following command:

$ kubectl get destinationrules -o yaml

You have configured Istio to route to the v1 version of the Bookinfo microservices, most importantly the reviews service version 1.

Test the new routing configuration

You can easily test the new configuration by once again refreshing the /productpage of the Bookinfo app in your browser. Notice that the reviews part of the page displays with no rating stars, no matter how many times you refresh. This is because you configured Istio to route all traffic for the reviews service to the version reviews:v1 and this version of the service does not access the star ratings service.

You have successfully accomplished the first part of this task: route traffic to one version of a service.

Route based on user identity

Next, you will change the route configuration so that all traffic from a specific user is routed to a specific service version. In this case, all traffic from a user named Jason will be routed to the service reviews:v2.

This example is enabled by the fact that the productpage service adds a custom end-user header to all outbound HTTP requests to the reviews service.

Istio also supports routing based on strongly authenticated JWT on ingress gateway, refer to the JWT claim based routing for more details.

Remember, reviews:v2 is the version that includes the star ratings feature.

  1. Run the following command to enable user-based routing:
Zip
$ kubectl apply -f @samples/bookinfo/networking/virtual-service-reviews-test-v2.yaml@

You can confirm the rule is created using the following command:

$ kubectl get virtualservice reviews -o yaml
apiVersion: networking.istio.io/v1beta1
kind: VirtualService
...
spec:
  hosts:
  - reviews
  http:
  - match:
    - headers:
        end-user:
          exact: jason
    route:
    - destination:
        host: reviews
        subset: v2
  - route:
    - destination:
        host: reviews
        subset: v1
  1. On the /productpage of the Bookinfo app, log in as user jason.

    Refresh the browser. What do you see? The star ratings appear next to each review.

  2. Log in as another user (pick any name you wish).

    Refresh the browser. Now the stars are gone. This is because traffic is routed to reviews:v1 for all users except Jason.

You have successfully configured Istio to route traffic based on user identity.

Understanding what happened

In this task, you used Istio to send 100% of the traffic to the v1 version of each of the Bookinfo services. You then set a rule to selectively send traffic to version v2 of the reviews service based on a custom end-user header added to the request by the productpage service.

Note that Kubernetes services, like the Bookinfo ones used in this task, must adhere to certain restrictions to take advantage of Istio’s L7 routing features. Refer to the Requirements for Pods and Services for details.

In the traffic shifting task, you will follow the same basic pattern you learned here to configure route rules to gradually send traffic from one version of a service to another.

Cleanup

  1. Remove the application route rules:
Zip
$ kubectl delete -f @samples/bookinfo/networking/virtual-service-all-v1.yaml@
  1. If you are not planning to explore any follow-on tasks, refer to the Bookinfo cleanup instructions to shutdown the application.
Was this information useful?
Do you have any suggestions for improvement?

Thanks for your feedback!